Alpharetta Floor Coating installs garage, concrete and industrial floor coatings for homeowners and businesses across Alpharetta, GA. Polyaspartic has become the coating homeowners ask for by name, usually after hearing it goes down in a day and does not yellow in the sun. Both of those things are generally true, and both are part of why it costs more than a standard epoxy floor.
Here is a straight look at polyaspartic pricing, what pushes it up, and when the extra spend earns its keep.
Typical polyaspartic floor coating cost
Published cost data puts professionally installed polyaspartic floor coating at roughly five to twelve dollars per square foot, materials and labor included. HomeGuide breaks that into about two to six dollars per square foot in materials and three to six dollars in labor, with labor making up the larger share of most projects.
What that means by garage size
- One-car garage, around 250 square feet: roughly $1,250 to $3,000
- Two-car garage, around 400 to 576 square feet: roughly $2,000 to $6,900
- Three-car garage, around 750 square feet: roughly $3,750 to $9,000
These are industry reference ranges rather than a quote. The condition of your concrete decides where in the band a real floor lands, and a slab needing heavy repair can sit outside it.
Why polyaspartic costs more than epoxy
Material chemistry
Polyaspartic is an aliphatic polyurea. The raw materials cost more than standard epoxy resins, and the products are engineered for UV stability and fast cure rather than for low price.
Working time and crew skill
Fast cure is a benefit for you and a constraint for the installer. The working window is short, so the crew has to move deliberately and know the product. That skill is priced into the job.
Same preparation, higher expectations
Polyaspartic does not skip preparation. The slab still has to be ground, repaired, and profiled properly, and because the finished floor is expected to last longer, cutting corners underneath makes even less sense. Surface preparation is the same line item it would be for any system.
What changes the price on a real floor
Condition of the concrete
Old paint, tile adhesive, a failed DIY kit, or deep oil staining all add removal time. Spalled or pitted slabs need resurfacing before coating. This is consistently the largest swing factor in any coating quote.
Moisture testing and mitigation
Moisture testing is inexpensive and worth doing. If the slab reads high, a mitigation primer is added, which raises cost but prevents the coating from blistering later. Below grade and older Alpharetta slabs are the ones to watch.
System build
A single pigmented coat with a clear topcoat costs less than a full flake broadcast system. Adding decorative flake increases both material and labor, since the flake has to be broadcast, scraped back, and sealed.
Texture and safety additives
Anti-slip aggregate adds a small amount per square foot. In wet areas or on sloped garage floors, a slip resistant finish is usually money well spent.
Job size and access
Per square foot rates usually fall as area grows. Tight spaces, heavy edge work, and floors that have to be emptied first add labor.
Polyaspartic compared with epoxy and polyurea
Epoxy typically runs about four to ten dollars per square foot installed, so it starts lower. Polyurea commonly falls around five to ten dollars. Polyaspartic sits at the top of that group, and buys you three things: a much shorter return-to-service window, strong UV stability so the color holds near a sunlit garage door, and good flexibility over concrete that moves slightly with temperature.
If the floor is in a basement with no direct light and the schedule is relaxed, epoxy may be the sensible spend. If the garage door faces afternoon sun, or you need the space back quickly, polyaspartic is usually the better fit. Our polyaspartic floor coating page goes deeper on where it performs best.
Is polyaspartic worth the extra cost?
It depends on what you are optimizing for. Look at it over the life of the floor rather than at the invoice. A system that holds its color and resists abrasion for many years can end up cheaper than a lower cost coating that needs redoing sooner, especially once you count the disruption of emptying a garage twice.
Where polyaspartic does not pay off is over a poorly prepared slab. No chemistry survives bad preparation. If a quote is low because the preparation is thin, the coating name on the proposal does not matter.
Frequently asked questions
Can polyaspartic really be installed in one day?
In many residential garages, yes. Fast cure chemistry allows coats to be applied the same day, with the floor usually walkable that evening. Vehicle traffic typically waits a little longer, and the exact timing depends on conditions.
Does polyaspartic yellow like epoxy?
Aliphatic polyaspartic is UV stable, so it resists the yellowing that standard epoxy can show in direct sunlight. That is one of its main advantages near an open garage door.
Is polyaspartic more slippery than epoxy?
On its own, a smooth topcoat of any chemistry can be slick when wet. Traction comes from the aggregate broadcast into the topcoat, not from the resin family.
Can polyaspartic go over an existing coating?
Sometimes, if the old coating is sound and compatible. More often the old finish is removed so the new system bonds to concrete. We test adhesion before deciding.
Why do quotes vary so much for the same product?
Because the product is a small part of the job. Preparation method, number of coats, film thickness, repairs included, and whether moisture testing is done all change the number far more than the resin does.
Get a polyaspartic quote for your floor
Ranges are useful for budgeting and useless for deciding. Call +14706844629 and we will look at your slab, test it, and give you a number that reflects the floor you actually have. We work throughout Alpharetta and the surrounding North Atlanta area.
